---
title: What Is a Slurry Pump? Types, Wet Parts &amp; How It Works
date: 2026-09-15T07:26:19Z
modified: 2026-10-10T08:01:24Z
permalink: "https://www.defucc.com/blog/centrifugal-pump/slurry-pump-types-wet-parts-how-it-works/"
type: post
status: publish
excerpt: ""
wpid: 3038
categories:
  - centrifugal pump
featured_image: "https://www.defucc.com/wp-content/uploads/2026/10/image2-2.jpg"
featured_image_alt: Cutaway slurry pump showing abrasive solids flowing through the impeller and wear-resistant wet parts.
timestamp: 2026-10-10T08:01:24Z
tags:
  - centrifugal pump
---

## **Quick answer**

A slurry pump moves liquids containing abrasive solids such as mineral particles, sand, or coal. Its wet parts are designed to withstand the wear these solids cause as they pass through the pump. Common slurry pump types include horizontal and vertical designs.

## **What Is a Slurry Pump?**

A slurry pump is designed to move a mixture of liquid and suspended solids. Many slurry pumps use a centrifugal design, but their construction has to account for particles that would cause excessive wear in equipment intended for clean water.

The slurry pump working principle is similar to that of a centrifugal water pump. Slurry enters the eye of the rotating impeller, which transfers energy to the mixture. The slurry moves outward into the casing and then toward the discharge.

The difference is what travels through the pump. Sand, ore, ash, and other solids can strike or rub against internal surfaces as they move.

## **How Do Abrasive Solids Change Pump Design?**

It’s possible to design a clean-water pump around a liquid containing minimal or no suspended material. In contrast, a slurry pump has to withstand the abrasion these solids cause while accommodating them.

Based on the design, this can include larger flow passages, replaceable liners, and thicker sections in areas exposed to wear. Operating speed can also affect wear, as higher particle velocity can increase erosion.

You also need to pay attention to the slurry itself. Larger or harder particles can wear internal surfaces differently from finer solids. The concentration of those particles can affect how the mixture behaves as it moves through the pump. These variables, along with operating conditions, can also affect [slurry pump efficiency](https://www.defucc.com/wp-content/uploads/wp-mfa-exports/post/how-to-maximise-mining-slurry-pump-efficiency.md).

## **What Are the Main Slurry Pump Wet Parts?**

![](https://www.defucc.com/wp-content/uploads/2026/10/b37fc7ec-fc75-428f-b3b9-acc2a5a198a6.jpg)

Slurry pump wet parts are the components that come into direct contact with the pumped mixture. These are the parts most exposed to abrasion.

In a lined horizontal slurry pump, they can include the impeller, volute liner, throat bush, and frame plate liner. The impeller transfers energy to the slurry, while the liners protect the surrounding pump structure from direct wear.

DEFUCC uses high chrome on friction-exposed components in its [MA&MH&ML slurry pump range](https://www.defucc.com/product/mamhml-slurry-pump/), including the impeller, volute liner, throat bush, and frame plate liner insert. Hard-metal or rubber wet parts are available depending on the requirements of the slurry.

## **What Are the Main Slurry Pump Types?**

Two common slurry pump types are horizontal and vertical designs. These terms describe the orientation of the pump shaft.

Horizontal slurry pumps have a horizontally positioned shaft and are widely used for process duties such as transferring abrasive slurry. Vertical slurry pumps use a vertical shaft and are commonly installed in sumps or pits.

The suitable orientation depends on the installation and required duty rather than one type being better in every application.

## **How Do Closed, Open, and Semi-Open Impellers Differ?**


Shrouds are present on both sides of the vanes in a closed impeller. Although it can deliver good hydraulic efficiency, its passages still have to accommodate the solids being pumped.

A shroud is only present on one side in a semi-open impeller. An open impeller comes without a rear or front shroud around its vanes. Different balances between solids passage, wear, and efficiency are achieved with these arrangements.

At DEFUCC, we offer different impeller options for our slurry pump range, including designs for larger particles and high efficiency.

## **Which Wet-Part Material Should You Choose?**

High-chrome alloys are commonly used where abrasive wear is severe. DEFUCC specifically uses high chrome for friction-exposed parts in its MA&MH&ML pumps.

Natural rubber can suit some fine-particle abrasive or corrosive slurries because its elasticity helps absorb particle impact. Polyurethane is another abrasion-resistant option used in suitable slurry pump designs.

Material selection depends on the actual slurry. Particle characteristics, liquid chemistry, and operating temperature all influence which material can provide suitable wear life. These are also useful points to compare when evaluating [mining slurry pump manufacturers](https://www.defucc.com/wp-content/uploads/wp-mfa-exports/post/top-mining-slurry-pump-manufacturers.md).

## **How Is a Slurry Pump Different From a Water Pump?**

The main difference is the medium each pump is designed to handle. A conventional water pump is generally intended for water with little abrasive material. A slurry pump has to move suspended solids without experiencing unacceptable wear or blockage.

This can require wear-resistant materials, larger passages, and replaceable wet parts. These features can trade some hydraulic efficiency for improved solids handling and wear life.

The distinction becomes important when water contains some solids but isn’t a dense abrasive slurry. We explain this middle ground in our guide to [slurry pumps and solids handling dewatering pumps](https://www.defucc.com/wp-content/uploads/wp-mfa-exports/post/slurry-pump-vs-dewatering-pump.md).

## **Where Are Slurry Pumps Used?**

Mining and mineral processing are major applications because ore and tailings can contain abrasive particles. Slurry pumps also move sand and mud and are used in dredging operations.

Power plants may use them to handle abrasive ash mixtures. Coal washing creates another slurry-handling duty involving suspended coal and mineral particles.

DEFUCC’s MA&MH&ML range is used for mine dewatering, power plants, coal washing, sand and mud pumping, dredging channels, and chemical plants.

## **FAQs**

### **Can a Slurry Pump Handle Sand?**

Yes. A suitable slurry pump can handle sand suspended in liquid, but it still needs to be selected for the expected solids and hydraulic duty.

### **Why Do Slurry Pumps Use Replaceable Wet Parts?**

Abrasive particles gradually wear surfaces that contact the slurry. Replaceable wet parts allow worn components to be renewed without replacing the entire pump.

### **Are Slurry Pumps Less Efficient Than Water Pumps?**

They can be. Features that improve solids passage and wear resistance can reduce hydraulic efficiency compared with a clean-water pump optimized for liquid service.

[Get Free Quote](https://www.defucc.com/wp-content/uploads/wp-mfa-exports/page/contact.md)



Welcome to Our Blog!
Professional Dewatering Pump Manufacturer

 Written by the Engineering & Solutions Team at WENZHOU DEFU MACHINERY CO., LTD. Backed by 3 manufacturing bases and over 10 years of expertise as a leading dewatering pump manufacturer, our team is dedicated to sharing practical dewatering pump insights and engineered fluid handling solutions for global projects.

 [ Contact Us → ](https://www.defucc.com/wp-content/uploads/wp-mfa-exports/page/contact.md) 

 ![WENZHOU DEFU MACHINERY CO., LTD. - Dewatering Pump Manufacturer](https://defucc.b-cdn.net/wp-content/uploads/2025/06/2-1-1--768x534.jpg)