Kurzantwort
A wastewater level sensor should be chosen by the control job, not the technology label. Use a float switch for simple start/stop and high-level alarm, ultrasonic for continuous non-contact measurement in a clean airspace, and radar where foam, vapor or grease make ultrasonic readings unreliable. Confirm the wet well, required output and backup alarm before comparing price. DEFU builds self-priming sewage pumps for lift stations and reviews the level, suction and control arrangement with the pump selection before finalizing the quote.
The Three Sensor Types at a Glance
There is no single best wastewater level sensor for every wet well. A lift station needs two things from a level device: a command to start or stop a pump, and a reading the operator can trust. Some sensors do only the first. Others do both.

| Typ | What it does | Best fit | Watch for |
|---|---|---|---|
| Float switch | Closes a contact when the liquid reaches a set height | Start/stop, lead/lag, high-level alarm | Fixed points only; rags and grease can foul the float |
| Ultrasonic | Times a sound pulse reflected from the surface | Continuous level and trend data | Foam, vapor, condensation and turbulence |
| Radar | Times a microwave reflection from the surface | Continuous level in vapor, dust or coated wells | Higher cost; foam and antenna buildup |
Two wells of the same depth can still need different sensors. The airspace, inflow pattern and maintenance access decide more than the headline measuring range.
Which Sensor Fits Your Lift Station Duty?
Start with four questions before you compare models.
- Does the controller need a switch or a measurement? A pump panel that only needs start, stop and alarm signals can use floats. A system that logs inflow, controls variable speed or reports to a central platform needs a continuous transmitter.
- What is in the airspace? Foam, grease, steam, dust and condensation each affect the three types differently.
- Who will clean and test it? A sensor mounted over a deep well with no safe access will not receive routine attention.
- What happens when it fails? Define the fail-safe direction and keep an independent high-level alarm.
Run that sequence first, then compare price. A lift station level sensor that is cheap to buy but hard to reach often costs more through callouts and lost pump control. The lift station selection guide covers wet-well volume, duty and standby in more detail.
Sewage Lift Station Pumps: Buyer Guide for Municipal Projects
A sewage pump lift station pumps wastewater from a lower elevation to a higher elevation when gravity flow is insufficient.
Read ArticleFloat Switches: Simple Control That Still Works
A float switch is a switch, not a measuring instrument. It tells the panel that the level has reached a point. For many small and medium stations, that is enough.
A sewage pump float switch is often used in groups: one to start the pump, one to stop it, and one for a high-level alarm. The wide switching band reduces starts, which suits a pump that has a limit on starts per hour. There are no electronics in the well, and most maintenance technicians can test and replace a float without special tools.
The weaknesses are mechanical. Grease and rags can weigh down or jam the float. A tethered float can wrap around a pipe in a swirling well. Turbulence can make the contact chatter. Cable insulation can fail in a corrosive atmosphere.
Choose a guided float or a stilling well where the surface is rough. Keep the float out of the inlet stream, and set the stop level high enough to keep the suction inlet submerged.
Do Ultrasonic Sensors Handle Wastewater?
Yes, when the path between the sensor and the liquid is clear. For ultrasonic level sensor wastewater duty, the airspace decides how well the reading holds. A covered well, limited foam, stable vapor and a fixed mounting point protect the transducer.
The sensor sends a sound pulse downward and times the echo. It never touches the liquid, so grease and grit do not wear the measuring element. That makes it a practical choice for continuous reading and trend logging.
The limits sit in the airspace. Thick or fresh foam can absorb the pulse. Steam and condensation on the face weaken it. Strong drafts, drops from an inlet pipe and reflections from walls or ladders can confuse the echo. Every ultrasonic unit also has a dead band near the face where it cannot measure.
Mount the sensor perpendicular to the surface, away from the inlet and any obstruction in the beam. If the surface is turbulent, a stilling well or bypass chamber gives the pulse a quiet path. Check the range against the full well depth, including the dead band, rather than the headline maximum.
When Should You Choose Radar Over Ultrasonic?
Radar sends a microwave signal and measures the reflection. It does not rely on the speed of sound, so air temperature, vapor and dust affect it far less than they affect ultrasonics. Narrow-beam units suit slim wet wells because they avoid echoes from walls and ladders.
That makes radar a strong option where ultrasonic sensors have failed more than once, or where the well is difficult to access for cleaning. The higher purchase price can reduce repeat visits in those conditions.
Radar still has limits. Foam reflects the signal, but loose or deep foam can scatter it, so confirm performance for your foam type. Condensation and buildup on the antenna can weaken the echo. Mounting height, blocking distance and the surrounding metalwork still matter. Radar does not fix a poor mounting location.
How Do Foam, Grease and Rags Change the Answer?
Foam is the clearest dividing line. It is the first condition that upsets an ultrasonic reading. Radar usually copes better, but it should be checked against the actual foam, not a general claim. A float can still work in foam, although foam clinging to the float may change its movement.

Grease favors non-contact sensors because there is nothing in the liquid to coat. A float in a greasy well needs a cleaning routine, and the tether should be inspected at the same time.
Rags and long fibers favor non-contact sensors for a different reason: they can wrap around a float and hold it in one position. In stations with heavy rag loads, the pump’s solids passage matters as much as the sensor. A large passage helps, but it does not remove the need for access to clear a blockage.
Corrosion is the fourth condition. Check the housing, cable jacket and mounting hardware against the atmosphere in the well, not only against the liquid.
What Else Belongs in the Sensor Specification?
A wastewater level sensor must also connect cleanly to the panel. Include these items in the inquiry:
- Output type and range, matched to the controller or telemetry unit
- Supply voltage and cable length
- Enclosure rating and area classification for the site
- Mounting bracket, standpipe or stilling well
- Measuring range, dead band and accuracy at the working depth
- Fail-safe direction and alarm behavior
- Calibration method, spare parts and expected cleaning access
Ask for a datasheet and wiring diagram with the quotation. That lets the panel builder confirm the input before the equipment arrives.
Non-Clog Sewage Pumps: 6 Specifications to Check Before an RFQ
For a non-clog pump , also verify suction lift, suction-pipe diameter and length, fittings, airtightness, and priming procedure.
Read ArticleMatching Level Control to the Pump Package
The sensor and the pump are selected together because the level settings depend on the pump curve and the wet well. A self-priming pump installed above the liquid level keeps the motor and controls out of the wet well, and the suction pipe does the work below.
DEFUs JT/JU self-priming sewage pumps are built for this layout. They are used for wastewater transfer where solids passage and maintenance access matter. The selected JT or JU model sets solids passage, suction lift, wetted materials and drive. Cast iron or stainless steel 304/316/316L wetted parts are available, with diesel, electric or bare-pump drive options.
Der DJ-Serie reaches 468 m³/h and 60 m of head, with 76 mm solids passage. Where flow and head split differently, the TX/TH range puts TX at up to 1,021.5 m³/h and TH at up to 84.4 m of head.
Set the levels around those facts:
- Stop level keeps the suction inlet submerged and avoids vortexing or air entry.
- Start level sets the usable wet-well volume and the number of starts per hour.
- Alarm level sits below the overflow point and triggers an independent switch.
- Alternation shares run time between duty and standby pumps.
A continuous sensor gives better trend data. A float gives a clear, simple command. Many stations use both: a transmitter for operation and a float for backup. If the application is new, the self-priming pump guide explains the suction conditions that affect the layout.
For documentation, DEFU operates an ISO 9001 quality management system. You can request the selected pump curve, materials list, dimensional drawing and test records with the order.
JT JU selbstansaugende Abwasserpumpe
Die selbstansaugende, verstopfungsfreie Abwasserpumpe der Serie JT&JU ist der Standard für industrielle Anwendungen und Abwasserentsorgung.
Grubenentwässerungspumpen erkundenAbschluss
Choose the sensor by the job it must do. Float switches remain the simplest answer for start/stop and alarm duty. Ultrasonic sensors give continuous data where the airspace is clean. Radar costs more but earns it back in vapor, dust or hard-to-access wells. In every case, confirm foam, grease, mounting and the backup alarm before you compare price.
When you request a wastewater level sensor for a pump package, send DEFU the flow and head, wet-well dimensions, liquid and solids details, foam or grease conditions, preferred sensor output, control sequence, quantity and destination. We can then review the pump and level arrangement together and quote the right configuration. For sewage duty, the non-clog pump RFQ checklist shows the additional data buyers usually need.
Willkommen auf unserem Blog!
Professioneller Hersteller von Entwässerungspumpen
Verfasst vom Engineering & Solutions Team der WENZHOU DEFU MACHINERY CO., LTD. Mit 3 Produktionsstandorten und über 10 Jahren Erfahrung als führender Hersteller von Entwässerungspumpen engagiert sich unser Team für die Bereitstellung praktischer Erkenntnisse im Bereich Entwässerungspumpen und technischer Lösungen für die Flüssigkeitsförderung in globalen Projekten.
Contact Us →






